Author Topic: Gaps between boards  (Read 984 times)

0 Members and 1 Guest are viewing this topic.

Iain

  • Crew
  • *
  • Posts: 4660
  • Gender: Female
  • Na sgrìobhaidh a Iain
  • Respect: +385
    • The Best Puppers
Gaps between boards
« on: April 25, 2020, 07:59:18 PM »
0
If I wanted to simulate board siding, what do y'all reckon would be the minimum width and depth of the slot between two 'boards' should be such that it will actually render when printed?
I like ducks

mu26aeh

  • Crew
  • *
  • Posts: 5376
  • Gender: Male
  • Respect: +3600
Re: Gaps between boards
« Reply #1 on: April 25, 2020, 08:36:32 PM »
0
Why is this making me think of another thread about board gap ?  :scared:

Carry on....

Dave V

  • Crew
  • *
  • Posts: 11220
  • Gender: Male
  • Foothills Farm Studios -- Dave's Model Railroading
  • Respect: +9327
Re: Gaps between boards
« Reply #2 on: April 25, 2020, 08:44:13 PM »
0
Why is this making me think of another thread about board gap ?  :scared:

Carry on....

LOL, I was about to say "ask Rapido" and then run for cover...   :trollface:

thomasjmdavis

  • Crew
  • *
  • Posts: 4080
  • Respect: +1104
Re: Gaps between boards
« Reply #3 on: April 25, 2020, 09:16:29 PM »
0
I suspect the real answer is that "beauty is in the eye of the beholder"- find a sample among your cars and models that you like, and measure it.  The easiest method to measure something like this, in my experience, is to use a feeler gauge (as used to set gaps in spark plugs)- it is easier to find and fit the correct feeler gauge "blade" than to try to measure a gap in thousandths with a micrometer or caliper (for me, anyway) and they commonly have blades as thin as 0.0015 inch.

What will make more difference than width and depth may be the degree of weathering.  My own opinion is that very fine lines (scored with the back of an Xacto blade, for instance) painted and given a light wash of india ink or similar thin wash (which will settle into the score lines), will read as more realistic than "gaps" of several thousandths wide.  So the answer here, in terms of 3D printing, might be "as small as allowed by the resolution of the printer."

I can already see that I will probably spend an hour going through tool boxes tomorrow trying to find my feeler gauge so I can measure the board spacing on my cars.
Tom D.

I have a mind like a steel trap...a VERY rusty, old steel trap.

Chris333

  • Crew
  • *
  • Posts: 18391
  • Respect: +5662
Re: Gaps between boards
« Reply #4 on: April 25, 2020, 10:04:30 PM »
+1
Depends what is printing it.

peteski

  • Crew
  • *
  • Posts: 32919
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +5323
    • Coming (not so) soon...
Re: Gaps between boards
« Reply #5 on: April 26, 2020, 12:43:23 AM »
0
LOL, I was about to say "ask Rapido" and then run for cover...   :trollface:

 :facepalm:  Hiding my head in the sand  Rapido Meat Reefer board gap.  :facepalm:
. . . 42 . . .

Iain

  • Crew
  • *
  • Posts: 4660
  • Gender: Female
  • Na sgrìobhaidh a Iain
  • Respect: +385
    • The Best Puppers
Re: Gaps between boards
« Reply #6 on: April 26, 2020, 02:39:52 AM »
0
Well, I did have a particular reefer in mind in terms of things I wanted to avoid.


In all seriousness, though ...

Depends what is printing it.

Probably a Photon.  I have decided to bite the bullet and get one once the pestilence settles down a bit.  However, I can go ahead and start designing for it now.
I like ducks

Chris333

  • Crew
  • *
  • Posts: 18391
  • Respect: +5662
Re: Gaps between boards
« Reply #7 on: April 26, 2020, 02:53:24 AM »
+1
I make boards .010" deep and wide anymore in HOn30.