« previous next »
Pages: [1]   Go Down

Author Topic: frosting clear styrene  (Read 1567 times)

0 Members and 1 Guest are viewing this topic.

rsn48

  • Crew
  • *
  • Posts: 360
  • Gender: Male
  • Respect: +1
frosting clear styrene
« on: November 20, 2014, 12:50:35 AM »
0
I want some frosted windows, in case I install lighting so you can't see in, on an "older" structure.  How do I frost the clear styrene.  I know about using Scotch tape but I'm not sure I trust it over a many year life.
Logged
Hind sight is always better than foresight, except for lost opportunity costs.

davefoxx

  • Crew
  • *
  • Posts: 11675
  • Gender: Male
  • TRW Plaid Member
  • Respect: +6802
Re: frosting clear styrene
« Reply #1 on: November 20, 2014, 01:02:29 AM »
0
Spray Dullcote on the "inside" of the windows.  This doesn't cause the windows to look matte from the outside, but they will appear frosted.

Hope this helps,
DFF
Logged

Member: ACL/SAL Historical Society
Member: Wilmington & Western RR
A Proud HOer
BUY ALL THE TRAINS!

peteski

  • Crew
  • *
  • Posts: 32958
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +5343
    • Coming (not so) soon...
Re: frosting clear styrene
« Reply #2 on: November 20, 2014, 01:38:07 AM »
0
Quote from: davefoxx on November 20, 2014, 01:02:29 AM
Spray Dullcote on the "inside" of the windows.  This doesn't cause the windows to look matte from the outside, but they will appear frosted.

Hope this helps,
DFF

That's exactly what I was going to recommend!  :)   Or any flat clear coating (there should be water-based versions available).
Logged
. . . 42 . . .

rsn48

  • Crew
  • *
  • Posts: 360
  • Gender: Male
  • Respect: +1
Re: frosting clear styrene
« Reply #3 on: November 20, 2014, 02:35:10 PM »
0
Thanks, that's too easy.
Logged
Hind sight is always better than foresight, except for lost opportunity costs.

peteski

  • Crew
  • *
  • Posts: 32958
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +5343
    • Coming (not so) soon...
Re: frosting clear styrene
« Reply #4 on: November 20, 2014, 04:43:49 PM »
0
Ok then, take some 400 grit wet/dry sandpaper and sand one side of the styrene.  Is that difficult enough? :D
Logged
. . . 42 . . .

rsn48

  • Crew
  • *
  • Posts: 360
  • Gender: Male
  • Respect: +1
Re: frosting clear styrene
« Reply #5 on: November 20, 2014, 06:27:48 PM »
0
I'm doing a lot of scratch building right now, and I sand...sand...sand.... sand...
Logged
Hind sight is always better than foresight, except for lost opportunity costs.

tom mann

  • Administrator
  • Crew
  • *****
  • Posts: 10917
  • Representing The Railwire on The Railwire
  • Respect: +1014
    • http://www.chicagoswitching.com
Re: frosting clear styrene
« Reply #6 on: November 21, 2014, 10:00:37 AM »
0
I would mist on some grimy colors on the inside, so the building doesn't look like some Christmas display when lit up. :tommann:
Logged

rsn48

  • Crew
  • *
  • Posts: 360
  • Gender: Male
  • Respect: +1
Re: frosting clear styrene
« Reply #7 on: November 21, 2014, 03:57:20 PM »
0
I building a modern granary that is still standing on the Canadian Prairie in Morrin Alberta, plans from MR February 2002.  I was going to show the specific picture but thought you might enjoy looking at some of the strange Canadian granaries still standing.

The one I am modeling is titled "Starland (Morrin, Alberta) and the small office in front is what I am working on now.  I just spray painted the inside of the office with Testor's flat black to tone down lighting.

You have to scroll down a ways to see the Starland Morrin granary:

http://vanishingsentinels.blogspot.ca/2006/02/agricore-elevators.html
Logged
Hind sight is always better than foresight, except for lost opportunity costs.

mcjaco

  • Crew
  • *
  • Posts: 1714
  • Respect: +110
Re: frosting clear styrene
« Reply #8 on: November 25, 2014, 03:55:48 PM »
0
I've mistakenly got Testors Liquid Cement on the back side of some block windows on the Walthers Geo. Printing building.  Glazed them quite nicely.   :facepalm:
Logged
~ Matt

Kisatchie

  • Crew
  • *
  • Posts: 4180
  • Gender: Male
  • Respect: +62
Re: frosting clear styrene
« Reply #9 on: November 25, 2014, 04:03:05 PM »
0
Quote from: mcjaco on November 25, 2014, 03:55:48 PM
I've mistakenly got Testors Liquid Cement on the back side of some block windows on the Walthers Geo. Printing building.  Glazed them quite nicely.   :facepalm:


Hmm... you stole Kiz's
technique...

Logged
Two scientists create a teleportation ray, and they try it out on a cricket. They put the cricket on one of the two teleportation pads in the room, and they turn the ray on.
The cricket jumps across the room onto the other pad.
"It works! It works!"

pnolan48

  • Crew
  • *
  • Posts: 1754
  • Respect: +136
Re: frosting clear styrene
« Reply #10 on: November 28, 2014, 09:14:47 PM »
0
I spray the windows from the outside, along with the rest of the structure. It's frosted enough for me.
Logged
Pages: [1]   Go Up
« previous next »