Author Topic: Weekend Update 3/7/21  (Read 8392 times)

0 Members and 3 Guests are viewing this topic.

Iain

  • Crew
  • *
  • Posts: 4656
  • Gender: Female
  • Na sgrìobhaidh a Iain
  • Respect: +372
    • The Best Puppers
Re: Weekend Update 3/7/21
« Reply #30 on: March 06, 2021, 11:38:05 PM »
+15
[ Guests cannot view attachments ]

I (mostly) built a Micron Art truck.  Up to this point, everything is soldered, contrary to the directions which explicitly say not to.  The wheels, cab roof, and bed will all be glued on after painting is done with the idea that it'll be easier to paint things with them out of the way.

Speaking of Micron Art, what happened to them?  This was my first kit of theirs and it was a rather fun build.
I like ducks

nickelplate759

  • Crew
  • *
  • Posts: 3332
  • Respect: +1035
Re: Weekend Update 3/7/21
« Reply #31 on: March 06, 2021, 11:41:22 PM »
0
Yikes!  Either that's a lot of tiny soldering (and very well done!) or you've swiped Peteski's giant comedy dime.
George
NKPH&TS #3628

I'm sorry Dave, I'm afraid I can't do that.

bbussey

  • Crew
  • *
  • Posts: 8881
  • Gender: Male
  • Respect: +4709
    • www.bbussey.net
Re: Weekend Update 3/7/21
« Reply #32 on: March 06, 2021, 11:54:38 PM »
0
Another way is to just use the shell function.  Use the thickness of the rectangular solid as your shell thickness.  The advantage is it will create a uniform thickness, the disadvantage is the details on the inside wile be slightly smaller.

That's why you cheat by offsetting the surface profile, so that it doesn't shell a different profile.  Because no matter what thickness that is chosen for the part, the N scale end will be much thicker than the prototype and the relief will be wrong.  By offsetting, it creates the illusion of a proper thickness, especially with a chord running along the top edge.
Bryan Busséy
NHRHTA #2246
NSE #1117
www.bbussey.net


dem34

  • Crew
  • *
  • Posts: 1649
  • Gender: Male
  • Only here to learn through Osmosis
  • Respect: +1187
Re: Weekend Update 3/7/21
« Reply #33 on: March 07, 2021, 12:01:43 AM »
+5

I (mostly) built a Micron Art truck.  Up to this point, everything is soldered, contrary to the directions which explicitly say not to.  The wheels, cab roof, and bed will all be glued on after painting is done with the idea that it'll be easier to paint things with them out of the way.

Speaking of Micron Art, what happened to them?  This was my first kit of theirs and it was a rather fun build.

There was a discussion I think in product discussion that the owner was retiring.


Anyhow. Since everyone is busy this week.

Ballasted and wired. Leaning into this being a prototype for a layout that uses the  TOMAR style approach while also technically conforming to loose FreeMOn standards in compatibility.




PS. Anybody noticing their AZ rock ballast floating all of a sudden? It was only certain granules but gave me a panic when I saw it happen.
-Al

wcfn100

  • Crew
  • *
  • Posts: 8839
  • Respect: +1218
    • Chicago Great Western Modeler
Re: Weekend Update 3/7/21
« Reply #34 on: March 07, 2021, 12:06:10 AM »
0
That's why you cheat by offsetting the surface profile, so that it doesn't shell a different profile.  Because no matter what thickness that is chosen for the part, the N scale end will be much thicker than the prototype and the relief will be wrong.  By offsetting, it creates the illusion of a proper thickness, especially with a chord running along the top edge.

Even if it's still oversized, the shell will produce a thinner part than the offset which might be more important than relief detail on a drop end.

Jason

chessie system fan

  • Crew
  • *
  • Posts: 1143
  • Gender: Male
  • Respect: +645
Re: Weekend Update 3/7/21
« Reply #35 on: March 07, 2021, 12:08:06 AM »
0
Thanks for the design tips.  I might start a separate thread on dreadnought ends later with my results showing both methods.

You can “cheat” by incorporating the MTL coupler box into your solid model.

That's the plan and one of the last things I still need to design.
Aaron Bearden

bbussey

  • Crew
  • *
  • Posts: 8881
  • Gender: Male
  • Respect: +4709
    • www.bbussey.net
Re: Weekend Update 3/7/21
« Reply #36 on: March 07, 2021, 12:44:50 AM »
0
Thanks for the design tips.  I might start a separate thread on dreadnought ends later with my results showing both methods.

That's the plan and one of the last things I still need to design.

I sent you an email regarding the coupler box and a PM regarding the stamped ends.
Bryan Busséy
NHRHTA #2246
NSE #1117
www.bbussey.net


chuck geiger

  • Crew
  • *
  • Posts: 3255
  • Gender: Male
  • Las Piedras Railroad - Destination Desert
  • Respect: +2821
Re: Weekend Update 3/7/21
« Reply #37 on: March 07, 2021, 10:45:23 AM »
+15
The square is revised from last Sunday.



Chuck Geiger
provencountrypd@gmail.com



davefoxx

  • Crew
  • *
  • Posts: 11675
  • Gender: Male
  • TRW Plaid Member
  • Respect: +6801
Re: Weekend Update 3/7/21
« Reply #38 on: March 07, 2021, 11:00:29 AM »
+1
I (mostly) built a Micron Art truck.  Up to this point, everything is soldered, contrary to the directions which explicitly say not to.

You, rebel, you.  :trollface:

DFF

Member: ACL/SAL Historical Society
Member: Wilmington & Western RR
A Proud HOer
BUY ALL THE TRAINS!

gi-depp

  • Crew
  • *
  • Posts: 93
  • Gender: Male
  • Respect: +358
Re: Weekend Update 3/7/21
« Reply #39 on: March 07, 2021, 12:09:50 PM »
+9
Weathering a Gunderson 53' TTX patched Husky-Stack






Union Pacific, Amtrak, VRE and US Army

peteski

  • Crew
  • *
  • Posts: 32884
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +5310
    • Coming (not so) soon...
Re: Weekend Update 3/7/21
« Reply #40 on: March 07, 2021, 12:51:35 PM »
0

I (mostly) built a Micron Art truck.  Up to this point, everything is soldered, contrary to the directions which explicitly say not to.  The wheels, cab roof, and bed will all be glued on after painting is done with the idea that it'll be easier to paint things with them out of the way.

Speaking of Micron Art, what happened to them?  This was my first kit of theirs and it was a rather fun build.

That looks good!  I also prefer soldering them, and like you I also use CA and/or epoxy for some parts.

As for Micron Art status, The business is unfrrtunatley shut down. See:
https://www.therailwire.net/forum/index.php?topic=47305.msg698620#msg698620
https://www.therailwire.net/forum/index.php?topic=50044.msg672335#msg672335
. . . 42 . . .

NtheBasement

  • Crew
  • *
  • Posts: 300
  • Respect: +289
    • Moving coal in N scale
Re: Weekend Update 3/7/21
« Reply #41 on: March 07, 2021, 02:14:48 PM »
+3
Spent some time learning how to take pictures suitable for focus stacking with my Canon SLR.  Its not straightforward.  Stacking software is CombineZP, a freebie.
Moving coal the old way: https://youtu.be/RWJVt4r_pgc
Moving coal the new way: https://youtu.be/sN25ncLMI8k

John

  • Administrator
  • Crew
  • *****
  • Posts: 13376
  • Respect: +3240
Re: Weekend Update 3/7/21
« Reply #42 on: March 07, 2021, 02:35:54 PM »
+11
Work In Progress

I picked up a lot of kits over the last 30 years -- this has been sitting in a box since at least 1998 or so .. time to get them built before my kid has to sell them on the white elephant table after I'm gone ..  :scared:

This isn't the final place on the layout - yet . I like the idea of old rail served brick buildings in urban areas .. also still need to finish detailing the model, add lighting, and some modern modifications ..










jpf94

  • Crew
  • *
  • Posts: 49
  • Respect: +64
Re: Weekend Update 3/7/21
« Reply #43 on: March 07, 2021, 02:46:15 PM »
0
Chris,

What drive did you put that on?   Looks fantastic.

BCOL 747

  • Crew
  • *
  • Posts: 227
  • Gender: Male
  • Respect: +143
Re: Weekend Update 3/7/21
« Reply #44 on: March 07, 2021, 03:45:18 PM »
0
Chris,

What drive did you put that on?   Looks fantastic.

It will fit the either the Atlas GP38/38-2/40/40-2 or the new Life Like GP38-2. It fits both very well. I didn't have to make any adjustments.

Chris