« previous next »
Pages: [1] 2 3   Go Down

Author Topic: Time to get started... SD40-2s and SD35 trucks  (Read 7767 times)

0 Members and 2 Guests are viewing this topic.

Ed Kapuscinski

  • Global Moderator
  • Crew
  • *
  • Posts: 24767
  • Head Kino
  • Respect: +9285
    • Conrail 1285
Time to get started... SD40-2s and SD35 trucks
« on: October 21, 2017, 02:24:05 PM »
0
It's time to get going on upgrading my SD40-2s to go full Conrail on em.

Now, before I start slicing up the existing trucks, can someone do me a favor?

If you have an Atlas SD35, can you see if its trucks fit in the IM SD40-2? If so, life will be wonderful (and I'll find a way to suitably show my appreciation).
Logged

mu26aeh

  • Crew
  • *
  • Posts: 5386
  • Gender: Male
  • Respect: +3609
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #1 on: October 21, 2017, 04:48:24 PM »
0
Not a direct swap Ed.  In following pictures, SD35 is back/top and SD40-2 is front/bottom (one with ton o' grease).  The Atlas truck has a housing around/above the gears that prevents it from being installed into the SD40-2 frame.  You can see this with the 1st picture, perhaps that could be removed ?  I did not investigate further into that option.





Logged

ncbqguy

  • Crew
  • *
  • Posts: 624
  • Gender: Male
  • Respect: +386
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #2 on: October 21, 2017, 05:04:02 PM »
0
Look at the early flexicoil side frame to see if it can be fitted to the late version gearbox rather than trying to make the gearboxes fit.   
I'd check myself but don't have any -2 units.
Charlie Vlk
Logged

Missaberoad

  • Crew
  • *
  • Posts: 3572
  • Gender: Male
  • Ryan in Alberta
  • Respect: +1172
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #3 on: October 21, 2017, 05:49:57 PM »
0
failing all else you can sand the detail off of the HTC truck and glue a thinned Flexicoil side frame to it...

I did this as an experiment with Kato trucks and the offset axle is hardly noticeable imo...

probably more work to type this then it was to do it, and looks better then a carved up HTC...  :D
Logged
Quote from: DirtyD79 on January 21, 2024, 12:21:37 PM
The Railwire is not your personal army.  :trollface:

mu26aeh

  • Crew
  • *
  • Posts: 5386
  • Gender: Male
  • Respect: +3609
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #4 on: October 21, 2017, 06:00:48 PM »
0
I tried swapping sideframes between the two and neither really wanted to mesh together.  It's close but something is off just enough....
Logged

daniel_leavitt2000

  • Crew
  • *
  • Posts: 6348
  • Respect: +1308
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #5 on: October 21, 2017, 06:27:16 PM »
0
I have been trying to prod CESM to make flexcoil side frames for the Atlas HTC truck, but he is not yet convinced to do it. This would be a perfect item for the acrylic black material.

Actually, he probably could do well with a better detailed HTC side frame as well. The Atlas one looks off, especially compared to the Kato version.

Letter writing campaign to CESM!
Logged
There's a shyness found in reason
Apprehensive influence swallow away
You seem to feel abysmal take it
Then you're careful grace for sure
Kinda like the way you're breathing
Kinda like the way you keep looking away

mu26aeh

  • Crew
  • *
  • Posts: 5386
  • Gender: Male
  • Respect: +3609
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #6 on: October 21, 2017, 06:33:26 PM »
0
Paging @dcutting .
Logged

Ed Kapuscinski

  • Global Moderator
  • Crew
  • *
  • Posts: 24767
  • Head Kino
  • Respect: +9285
    • Conrail 1285
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #7 on: October 21, 2017, 06:35:10 PM »
0
This would be the time!
Logged

coosvalley

  • Crew
  • *
  • Posts: 1405
  • Respect: +640
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #8 on: October 21, 2017, 08:45:58 PM »
0
Logged

bnsfdash8

  • Crew
  • *
  • Posts: 662
  • Respect: +1541
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #9 on: October 21, 2017, 10:45:38 PM »
+1
I used Kato trucks on my SD50. It took some modifying of the mechanism to get them to work though.

Logged
Reese
Modeling Norfolk Southern one loco at a time.

Ed Kapuscinski

  • Global Moderator
  • Crew
  • *
  • Posts: 24767
  • Head Kino
  • Respect: +9285
    • Conrail 1285
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #10 on: October 21, 2017, 11:47:36 PM »
0
Does anyone know if the HTC trucks under these are the same as the Atlas ones?
Logged

daniel_leavitt2000

  • Crew
  • *
  • Posts: 6348
  • Respect: +1308
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #11 on: October 22, 2017, 12:12:12 AM »
0
They are exactly the same as the Atlas HTC trucks.
Logged
There's a shyness found in reason
Apprehensive influence swallow away
You seem to feel abysmal take it
Then you're careful grace for sure
Kinda like the way you're breathing
Kinda like the way you keep looking away

crrcoal

  • Crew
  • *
  • Posts: 541
  • Respect: +86
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #12 on: October 22, 2017, 11:37:27 AM »
0
Hate to ask a stoopid question but could someone post a side by side comparison of the trucks? I'm not quite sure what the differences are you all are talking about.
Thanks!
Logged

dcutting

  • Crew
  • *
  • Posts: 359
  • Gender: Male
  • Respect: -57
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #13 on: October 22, 2017, 12:00:25 PM »
0
Quote from: daniel_leavitt2000 on October 21, 2017, 06:27:16 PM
I have been trying to prod CESM to make flexcoil side frames for the Atlas HTC truck, but he is not yet convinced to do it. This would be a perfect item for the acrylic black material.

Actually, he probably could do well with a better detailed HTC side frame as well. The Atlas one looks off, especially compared to the Kato version.

Letter writing campaign to CESM!

Wait... I thought that I did make flexicoilds for the HT-C truck...
Logged
David Cutting

mu26aeh

  • Crew
  • *
  • Posts: 5386
  • Gender: Male
  • Respect: +3609
Re: Time to get started... SD40-2s and SD35 trucks
« Reply #14 on: October 22, 2017, 12:32:52 PM »
0
Logged
Pages: [1] 2 3   Go Up
« previous next »