« previous next »
Pages: [1]   Go Down

Author Topic: Spot paint stripping plastic  (Read 1361 times)

0 Members and 1 Guest are viewing this topic.

daniel_leavitt2000

  • Crew
  • *
  • Posts: 6345
  • Respect: +1305
Spot paint stripping plastic
« on: February 13, 2015, 12:01:17 AM »
0
I want to strip just the door from a TLT newsprint car. The doors are glued in and I can not separate them. I want them to be brown, and the factory yellow paint is much to thick to paint over it. Is there any gell type paint remover that can to a specific, masked area?
Logged
There's a shyness found in reason
Apprehensive influence swallow away
You seem to feel abysmal take it
Then you're careful grace for sure
Kinda like the way you're breathing
Kinda like the way you keep looking away

peteski

  • Crew
  • *
  • Posts: 32952
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +5340
    • Coming (not so) soon...
Re: Spot paint stripping plastic
« Reply #1 on: February 13, 2015, 12:15:25 AM »
0
It would be quite difficult to do (IMO, not worth the effort).  But masking then sandblasting would probably work.  Do you have an air-eraser handy?

Most paint strippers for plastic are liquid. There used to be Chameleon Gel stripper but I'm not sure it is still being made. But even the gel was quite runny.
Logged
. . . 42 . . .

daniel_leavitt2000

  • Crew
  • *
  • Posts: 6345
  • Respect: +1305
Re: Spot paint stripping plastic
« Reply #2 on: February 13, 2015, 12:27:56 AM »
0
The whole product line is long gone. I was thinking about Easy Off, that foams up right?

I should invest in a media blaster.
Logged
There's a shyness found in reason
Apprehensive influence swallow away
You seem to feel abysmal take it
Then you're careful grace for sure
Kinda like the way you're breathing
Kinda like the way you keep looking away

peteski

  • Crew
  • *
  • Posts: 32952
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +5340
    • Coming (not so) soon...
Re: Spot paint stripping plastic
« Reply #3 on: February 13, 2015, 02:45:06 AM »
0
Quote from: daniel_leavitt2000 on February 13, 2015, 12:27:56 AM
The whole product line is long gone. I was thinking about Easy Off, that foams up right?

I should invest in a media blaster.

It is a liquid which does foam up but then the foam collapses back ... into liquid.  Way before it had a chance to actually soften the paint.
Logged
. . . 42 . . .

craigolio1

  • Crew
  • *
  • Posts: 2454
  • Respect: +1773
Re: Spot paint stripping plastic
« Reply #4 on: February 13, 2015, 01:12:16 PM »
0
Quote from: daniel_leavitt2000 on February 13, 2015, 12:01:17 AM
I want to strip just the door from a TLT newsprint car. The doors are glued in and I can not separate them. I want them to be brown, and the factory yellow paint is much to thick to paint over it. Is there any gell type paint remover that can to a specific, masked area?

I did this very thing using a Badger Hobby Sandblaster. I had a CN SD40-2w with sergeant stripes that I had to remove to paint the back end white (converting to an Expo 86 unit). I masked off the factory paint and then stripped the back end down below the roof line. Washed, remasked, painted, done.

Now that I have this tool I will never buy chemical strippers again.

Craig
Logged

Lemosteam

  • Crew
  • *
  • Posts: 5919
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +3666
    • Designer at Keystone Details
Re: Spot paint stripping plastic
« Reply #5 on: February 14, 2015, 06:52:42 PM »
0
Third the vote on the air eraser.  Used it on my polar express when some capillary action drew the spray paint into  some rivet areas along the roof. Media was aluminum oxide with no damage whatsoever.  It's very controllable but if you want to protect surrounding areas, I imagine taping it off would be good.
Logged
Pages: [1]   Go Up
« previous next »